What are the steps involved in front stabilizer bar link and bushing removal and installation on Kia Sportage?

The procedures that are used to remove the sway bar kit entail the following where the crossmember of the suspension is lowered and the sway bar kit is taken from behind; normally where there is harm on the bar, it is due to severe influences accorded to it from accidents that may have affected other significant apparatus and thus called for professional repair. Start the procedure with the removal of the wheel lug nuts, lifting of the front part of the car and placing on stands together with an application of park brake and placing of the rear wheels on blocks. Wheels need to be removed first, then use an Allen wrench to hold the ballstud and knock the nut off to get the link off the lower control arm / strut. For the 1997 and the models prior to that, the links are secured to the lower control arms by a bolt; the 2002 models and the models that come after it, the links are mounted to the front struts. Third, it is necessary to take out the sway bar brackets and Sway Bar Bushing and check the bushings for cracks or tears; if the bushings are damaged, put a new one in their place. Next, clean the bushings and lubricate them with silicone lubricant or vegetable oil and then assemble the bushings on to the bar, brackets and bolts followed by tightening until the specified torque tightness is achieved. For the models of Sportage, it is necessary to remove the lower cross bar of sway bar kit of an engine/transaxle subframe, and besides it is needed to lower the mentioned member also. One has to take out the nuts on the sway bar link rods and the bolts uncovering the lower control arm ball joint and front exhaust pipe. With regards to the 4 wheel drive, the driveshaft needs to be detached from the vehicle and the oil of the transfer case needs to be drained. You also have to unbolt the rear flange assembly and depending on the model of Montero, the intermediate shaft has to be disengaged from the steering gear. Remove the power steering fluid, and unbolt the pressure line fittings; supporting the engine/transaxle assembly and subframe with hydraulic jacks. Bolt securing the engine to the subframe, and subframe to the vehicle frame should be undone and the subframe lowered slightly to allow removal of the LB sway bar assembly and examination of the condition of the clamp bushes. Installation involves the opposite of what is required in removal in regard to fasteners, where all has to be tightened. At long last, fix the wheel and lugs and then lower the vehicle and uniformly tighten lugs to their required torque.

Genuine Kia Sportage Sway Bar Bushing

Stabilizer Sway Bar Bushing

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

15 Sway Bar Bushings found

View related parts
Kia Sportage Bush-Stabilizer Bar
Part Number: 548133S110
$11.28 MSRP: $15.87
You Save: $4.59 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2016-2024 Kia Sportage | 2.0L - Theta 2, 2.4L - Theta 2, 2.5L-THETA-III | Wagon - 5Door 5P, Wagon - Long 5Door 5P
View related parts
Kia Sportage Bush-Stabilizer Bar
Part Number: 555133N100
$16.41 MSRP: $23.08
You Save: $6.67 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2010-2013 Kia Sportage | 2.0L - Theta 2, 2.4L - Theta 2 | Wagon - 5Door 5P
View related parts
Kia Sportage Bush-Stabilizer Bar
Part Number: 548132S000
$14.02 MSRP: $19.72
You Save: $5.70 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bushing, Stabilizer Bar Bushing
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2010-2013 Kia Sportage | 2.0L - Theta 2, 2.4L - Theta 2 | Wagon - 5Door 5P
View related parts
Kia Sportage Bush-Stabilizer Bar
Part Number: 548132S100
$15.02 MSRP: $20.35
You Save: $5.33 (27%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2010-2013 Kia Sportage | 2.0L - Theta 2, 2.4L - Theta 2 | Wagon - 5Door 5P
View related parts
Kia Sportage Bush-Stabilizer Bar
Part Number: 555131F000
$9.66 MSRP: $13.58
You Save: $3.92 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bushing, Stabilizer Bar Bushing
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2005-2010 Kia Sportage | High Grade, Middle Grade | 2.0L, 2.0L - Beta, 2.7L, 2.7L - Delta | 5 Door Wagon, Wagon - 5Door 5P
View related parts
Kia Sportage Bush-Stabilizer Bar
Part Number: 548131F000
$14.49 MSRP: $20.38
You Save: $5.89 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bushing, Stabilizer Bar Bushing
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2005-2010 Kia Sportage | High Grade, Middle Grade | 2.0L, 2.0L - Beta, 2.7L, 2.7L - Delta | 5 Door Wagon, Wagon - 5Door 5P
View related parts
Kia Sportage Bush-Rear Stabilizer
Part Number: 555133S000
$13.99 MSRP: $19.68
You Save: $5.69 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bushing, Stabilizer Bar Bushing
- Position: Rear
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2014-2015 Kia Sportage | 2.0L - Theta 2, 2.4L - Theta 2 | Wagon - 5Door 5P
View related parts
Kia Sportage Bush-Stabilizer Bar
Part Number: 548132Y000
$14.95 MSRP: $21.03
You Save: $6.08 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bushing, Stabilizer Bar Bushing
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2014-2015 Kia Sportage | 2.0L - Theta 2, 2.4L - Theta 2 | Wagon - 5Door 5P
View related parts
Kia Sportage Bush-Stabilizer Bar
Part Number: 555133N200
$18.39 MSRP: $25.87
You Save: $7.48 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bushing, Stabilizer Bar Bushing
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2014-2015 Kia Sportage | 2.0L - Theta 2, 2.4L - Theta 2 | Wagon - 5Door 5P
View related parts
Kia Sportage Bush-Stabilizer Bar
Part Number: 54813D3000
$13.24 MSRP: $18.62
You Save: $5.38 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bushing, Stabilizer Bar Bushing
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2016-2022 Kia Sportage | 2.0L - Theta 2, 2.4L - Theta 2 | Wagon - 5Door 5P
View related parts
Kia Sportage Bush-Stabilizer Bar
Part Number: 55513F1000
$14.41 MSRP: $20.27
You Save: $5.86 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bushing, Stabilizer Assembly Bushing
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2023-2024 Kia Sportage | 1.6L-Gamma-II, 2.5L-THETA-III | Wagon - Long 5Door 5P
View related parts
Kia Sportage Bush-Stabilizer Bar
Part Number: 54813C1100
$9.85 MSRP: $13.85
You Save: $4.00 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bushing, Stabilizer Bar Bushing
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2023-2024 Kia Sportage | 1.6L-Gamma-II, 2.5L-THETA-III | Wagon - Long 5Door 5P
View related parts
Kia Sportage Bush-Rubber
Part Number: 0K01834156A
$5.93 MSRP: $8.04
You Save: $2.11 (27%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bush-Stabilizer Bar
- Replaced by: 0K01V34156
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 1997-2000 Kia Sportage | Low Grade, Middle Grade | 2.0L | 5 Door Wagon
View related parts
Kia Sportage BUSH-STABILIZER BAR
Part Number: 54813N9100
$15.75 MSRP: $22.15
You Save: $6.40 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2023-2024 Kia Sportage | 1.6L-Gamma-II, 2.5L-THETA-III | Wagon - Long 5Door 5P
View related parts
Kia Sportage Rubber-STABILIZER
Part Number: 0K01V34156
Product Specifications
- Other Name: Bush-Rubber; Bushing, Stabilizer Bar Bushing
- Manufacturer Note: YELLOW
- Replaces: 0K01834156A
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 1997-2002 Kia Sportage | High Grade, Low Grade, Middle Grade | 2.0L | 2 Door 5 Canvas Top, 5 Door Wagon

Kia Sportage Sway Bar Bushing

Indeed, the Kia Sportage Sway Bar Bushing is a very critical part that can greatly improve the dependability and usability of the Kia Sportage - a highly-ranked SUV for safety and fuel economy. These sway bar bushings have the critical function of dampening, road knocks and reducing noises making the ride comfortable for all passengers. Located at the supports of the sway bar, the Kia Sportage Sway Bar Bushing keeps the amount of lean in cornering in check, which is paramount for maneuvering stability. To fit different models of Sportage, these bushings are made for durability when it comes to day-to-day usage and proper handling and steering inclusion. Moreover, the Kia Sportage Sway Bar Bushing requires frequent lubrication because the bushing wear is a typical problem which results in sluggish steering and rattle sounds meaning that the bushing require to be replaced soon. These bushings are also important for safety and not only the comfort; that is why the Kia Sportage became the car with the title 'Top Safety Pick' according to the Insurance Institute for Highway Safety. Over time, Kia Sportage Sway Bar Bushing has been designed with reputable features that align with the car market to guarantee the drivers quality and efficiency in their driving. Over the years of Kia Sportage production, the quality of the components such as Sway Bar Bushing is critical in sustaining the vehicle position in the segment of SUVs.

If you're in search of top-notch, reasonably priced OEM Kia Sportage Sway Bar Bushing, then you've found the perfect spot. Our website boasts an extensive inventory of Kia Sportage Sway Bar Bushing, all priced at the market's premier price. Rest assured, every genuine part we offer comes with a warranty straight from the manufacturer.

Kia Sportage Sway Bar Bushing Parts Questions & Experts Answers

Bush-Stabilizer Bar
548131F000
Q: What are the steps involved in front stabilizer bar link and bushing removal and installation on Kia Sportage?
A: The procedures that are used to remove the Sway Bar Kit entail the following where the crossmember of the suspension is lowered and the sway bar kit is taken from behind; normally where there is harm on the bar, it is due to severe influences accorded to it from accidents that may have affected other significant apparatus and thus called for professional repair. Start the procedure with the removal of the wheel lug nuts, lifting of the front part of the car and placing on stands together with an application of park brake and placing of the rear wheels on blocks. Wheels need to be removed first, then use an Allen wrench to hold the ballstud and knock the nut off to get the link off the lower Control Arm / strut. For the 1997 and the models prior to that, the links are secured to the lower control arms by a bolt; the 2002 models and the models that come after it, the links are mounted to the front struts. Third, it is necessary to take out the sway bar brackets and Sway Bar Bushing and check the bushings for cracks or tears; if the bushings are damaged, put a new one in their place. Next, clean the bushings and lubricate them with silicone lubricant or vegetable oil and then assemble the bushings on to the bar, brackets and bolts followed by tightening until the specified torque tightness is achieved. For the models of Sportage, it is necessary to remove the lower cross bar of sway bar kit of an engine/transaxle subframe, and besides it is needed to lower the mentioned member also. One has to take out the nuts on the sway bar link rods and the bolts uncovering the lower control arm ball joint and front exhaust pipe. With regards to the 4 wheel drive, the driveshaft needs to be detached from the vehicle and the oil of the transfer case needs to be drained. You also have to unbolt the rear flange assembly and depending on the model of Montero, the intermediate shaft has to be disengaged from the steering gear. Remove the power steering fluid, and unbolt the pressure line fittings; supporting the engine/transaxle assembly and subframe with hydraulic jacks. Bolt securing the engine to the subframe, and subframe to the vehicle frame should be undone and the subframe lowered slightly to allow removal of the LB sway bar assembly and examination of the condition of the clamp bushes. Installation involves the opposite of what is required in removal in regard to fasteners, where all has to be tightened. At long last, fix the wheel and lugs and then lower the vehicle and uniformly tighten lugs to their required torque.