How can you safely replace a master cylinder without damaging the Kia Sorento's paint or finished surfaces?

Brake fluid can damage paint or finished surfaces, so it's important to cover all body parts and avoid spills during the procedure, cleaning up any spills immediately with water. Begin by disconnecting the cable from the negative terminal of the battery. For 2011 or later models, remove the air filter housing and air intake duct. Use a syringe or an old turkey baster to remove as much fluid as possible from the reservoir, then unplug the electrical connector for the brake fluid level warning switch. Place rags under the fittings and prepare caps or plastic bags to cover the ends of the lines once disconnected. Loosen the fittings at the ends of the brake lines where they enter the Brake Master Cylinder using a flare-nut wrench to prevent rounding off the flats. Carefully move the brake lines away from the Brake Master Cylinder and plug the ends to avoid contamination. Remove the nuts attaching the Brake Master Cylinder to the power brake booster and pull the Brake Master Cylinder off the studs, taking care not to spill fluid or bend the brake lines. If necessary, remove the brake lines going to the ABS actuator from the Brake Master Cylinder if they cannot be moved aside without damage. Before installing the new Brake Master Cylinder, bench bleed it by mounting it in a vise and attaching a pair of bleeder tubes to the outlet ports. Fill the reservoir with the recommended brake fluid and slowly push the pistons into the Brake Master Cylinder using a large Phillips screwdriver to expel air into the reservoir. Repeat this until no more air bubbles are present, then remove the bleed tubes one at a time and install plugs in the open ports to prevent leakage and air entry. Install the reservoir cover, then position the Brake Master Cylinder over the studs on the power brake booster, tightening the attaching nuts only finger tight initially. Thread the brake line fittings into the Brake Master Cylinder, adjusting the position slightly if needed to avoid stripping the threads. Tighten the mounting nuts to the specified torque and secure the brake line fittings. Fill the Brake Master Cylinder reservoir with fluid and bleed the Brake Master Cylinder and brake system by having an assistant pump the brake pedal, holding it to the floor while loosening the fitting nut to allow air and fluid to escape, repeating this until the fluid is clear of air bubbles. Keep plenty of rags on hand to catch any fluid, as brake fluid can ruin painted surfaces. If the Brake Master Cylinder-to-ABS actuator brake lines were removed, bleed those lines at the ABS control unit as well. Finally, complete the installation by reversing the removal steps and carefully testing the operation of the brake system before returning the vehicle to normal service.

Genuine Kia Sorento Brake Master Cylinder

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

17 Brake Master Cylinders found

View related parts
Kia Sorento Cylinder Assembly-Brake
Part Number: 585101U701
$220.38 MSRP: $306.08
You Save: $85.70 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Assembly-Brake Master
- Replaced by: 585101U801
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2009-2012 Kia Sorento | 2.4L - Theta 2, 3.5L - Lambda 2 | Wagon - 5Door 5P, Wagon - 5Door 7P
View related parts
Kia Sorento Booster & Master Cylinder Assembly
Part Number: 591003E450
$461.97 MSRP: $664.90
You Save: $202.93 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Booster Assembly
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2006-2008 Kia Sorento | High Grade, Middle Grade | 3.3L - Lambda, 3.8L, 3.8L - Lambda | 5 Door Wagon, Wagon - 5Door 5P
View related parts
Kia Sorento Cylinder Assembly-BRAKEM
Part Number: 585101U801
$213.95 MSRP: $306.08
You Save: $92.13 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Assembly-Brake Master; Master Cylinder
- Replaces: 585101U701
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2009-2012 Kia Sorento | 2.4L - Theta 2, 3.5L - Lambda 2 | Wagon - 5Door 5P, Wagon - 5Door 7P
View related parts
Kia Sorento Master Cylinder & Re
Part Number: 591203E550
$217.87 MSRP: $302.60
You Save: $84.73 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Master Cylinder & Reservoir Assembly
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2006-2008 Kia Sorento | 3.3L - Lambda, 3.8L - Lambda | Wagon - 5Door 5P
View related parts
Kia Sorento Booster & Master Cylinder
Part Number: 591003E560
$468.19 MSRP: $658.50
You Save: $190.31 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Booster & Master Cylinder Assembly
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2006-2008 Kia Sorento | 3.3L - Lambda, 3.8L - Lambda | Wagon - 5Door 5P
View related parts
Kia Sorento Master Cylinder & Re
Part Number: 591203E450
$212.38 MSRP: $303.83
You Save: $91.45 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Master Cylinder & Reservoir Assembly; Master Cylinder
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2006-2008 Kia Sorento | High Grade, Middle Grade | 3.3L - Lambda, 3.8L, 3.8L - Lambda | 5 Door Wagon, Wagon - 5Door 5P
View related parts
Kia Sorento Master Cylinder & Reservoir Assembly
Part Number: 591203E200
$211.39 MSRP: $302.42
You Save: $91.03 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Master Cylinder
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2003-2006 Kia Sorento | High Grade, Middle Grade | 3.5L | 5 Door Wagon
View related parts
Kia Sorento Master Cylinder & Reservoir Assembly
Part Number: 591203E300
$211.39 MSRP: $302.42
You Save: $91.03 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Master Cylinder
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2003-2006 Kia Sorento | High Grade, Middle Grade | 3.5L | 5 Door Wagon
View related parts
Kia Sorento Master Cylinder & Reservoir Assembly
Part Number: 591203E250
$214.83 MSRP: $307.33
You Save: $92.50 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Master Cylinder
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2003-2006 Kia Sorento | High Grade, Middle Grade | 3.5L | 5 Door Wagon
View related parts
Kia Sorento Master Cylinder & Reservoir Assembly
Part Number: 591203E350
$211.65 MSRP: $302.79
You Save: $91.14 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Master Cylinder
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2003-2006 Kia Sorento | High Grade, Middle Grade | 3.5L | 5 Door Wagon
View related parts
Kia Sorento Cylinder Assembly-Brake
Part Number: 58510R5000
$217.14 MSRP: $310.65
You Save: $93.51 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Master Cylinder
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2021-2023 Kia Sorento | 2.5L-THETA-III | Wagon - 5Door 6P, Wagon - 5Door 7P
View related parts
Kia Sorento Cylinder Assembly-Brake
Part Number: 585102W800
$230.96 MSRP: $330.42
You Save: $99.46 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Assembly-Brake Master; Master Cylinder
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2013-2014 Kia Sorento | 2.4L - Theta 2, 3.3L - Lambda 2 | Wagon - 5Door 5P, Wagon - 5Door 7P
View related parts
Kia Sorento Booster & Master Cylinder Assembly
Part Number: 591003E350
$480.81 MSRP: $706.04
You Save: $225.23 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Booster Assembly
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2003-2006 Kia Sorento | High Grade, Middle Grade | 3.5L | 5 Door Wagon
View related parts
Kia Sorento Booster & Master Cylinder Assembly
Part Number: 591003E200
$412.10 MSRP: $593.12
You Save: $181.02 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Booster Assembly
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2003-2006 Kia Sorento | High Grade, Middle Grade | 3.5L | 5 Door Wagon
View related parts
Kia Sorento Booster & Master Cylinder Assembly
Part Number: 591003E300
$418.86 MSRP: $602.85
You Save: $183.99 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Booster Assembly
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2003-2006 Kia Sorento | High Grade, Middle Grade | 3.5L | 5 Door Wagon
View related parts
Kia Sorento Booster & Master Cylinder Assembly
Part Number: 591003E250
$455.89 MSRP: $656.15
You Save: $200.26 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Booster Assembly
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2003-2006 Kia Sorento | High Grade, Middle Grade | 3.5L | 5 Door Wagon
View related parts
Kia Sorento Cylinder Assembly-Brake
Part Number: 58510C6800
$239.21 MSRP: $344.28
You Save: $105.07 (31%)
ADD TO CART
Product Specifications
- Other Name: Cylinder Assembly-Brake Master; Master Cylinder
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2015-2020 Kia Sorento | 2.0L - R, 2.0L - Theta 2, 2.4L - Theta 2, 3.3L - Lambda 2 | Wagon - 5Door 5P, Wagon - 5Door 7P

Kia Sorento Brake Master Cylinder

If you're in search of top-notch, reasonably priced OEM Kia Sorento Brake Master Cylinder, then you've found the perfect spot. Our website boasts an extensive inventory of Kia Sorento Brake Master Cylinder, all priced at the market's premier price. Rest assured, every genuine part we offer comes with a warranty straight from the manufacturer.

Kia Sorento Brake Master Cylinder Parts Questions & Experts Answers

Cylinder Assembly-BRAKEM
585101U801
Q: How can you safely replace a master cylinder without damaging the Kia Sorento's paint or finished surfaces?
A: Brake fluid can damage paint or finished surfaces, so it's important to cover all body parts and avoid spills during the procedure, cleaning up any spills immediately with water. Begin by disconnecting the cable from the negative terminal of the battery. For 2011 or later models, remove the air filter housing and air intake duct. Use a syringe or an old turkey baster to remove as much fluid as possible from the reservoir, then unplug the electrical connector for the brake fluid level warning switch. Place rags under the fittings and prepare caps or plastic bags to cover the ends of the lines once disconnected. Loosen the fittings at the ends of the Brake Lines where they enter the Brake Master Cylinder using a flare-nut wrench to prevent rounding off the flats. Carefully move the brake lines away from the Brake Master Cylinder and plug the ends to avoid contamination. Remove the nuts attaching the Brake Master Cylinder to the power brake booster and pull the Brake Master Cylinder off the studs, taking care not to spill fluid or bend the brake lines. If necessary, remove the brake lines going to the ABS actuator from the Brake Master Cylinder if they cannot be moved aside without damage. Before installing the new Brake Master Cylinder, bench bleed it by mounting it in a vise and attaching a pair of bleeder tubes to the outlet ports. Fill the reservoir with the recommended brake fluid and slowly push the pistons into the Brake Master Cylinder using a large Phillips screwdriver to expel air into the reservoir. Repeat this until no more air bubbles are present, then remove the bleed tubes one at a time and install plugs in the open ports to prevent leakage and air entry. Install the reservoir cover, then position the Brake Master Cylinder over the studs on the power brake booster, tightening the attaching nuts only finger tight initially. Thread the brake line fittings into the Brake Master Cylinder, adjusting the position slightly if needed to avoid stripping the threads. Tighten the mounting nuts to the specified torque and secure the brake line fittings. Fill the Brake Master Cylinder reservoir with fluid and bleed the Brake Master Cylinder and brake system by having an assistant pump the brake pedal, holding it to the floor while loosening the fitting nut to allow air and fluid to escape, repeating this until the fluid is clear of air bubbles. Keep plenty of rags on hand to catch any fluid, as brake fluid can ruin painted surfaces. If the Brake Master Cylinder-to-ABS actuator brake lines were removed, bleed those lines at the ABS control unit as well. Finally, complete the installation by reversing the removal steps and carefully testing the operation of the brake system before returning the vehicle to normal service.

Genuine Kia Sorento Brake Master Cylinder

17 Brake Master Cylinders found

Kia Sorento Cylinder Assembly-Brake

Kia Sorento Booster & Master Cylinder Assembly

Kia Sorento Cylinder Assembly-BRAKEM

Kia Sorento Master Cylinder & Re

Kia Sorento Booster & Master Cylinder

Kia Sorento Master Cylinder & Re

Kia Sorento Master Cylinder & Reservoir Assembly

Kia Sorento Master Cylinder & Reservoir Assembly

Kia Sorento Master Cylinder & Reservoir Assembly

Kia Sorento Master Cylinder & Reservoir Assembly

Kia Sorento Cylinder Assembly-Brake

Kia Sorento Cylinder Assembly-Brake

Kia Sorento Booster & Master Cylinder Assembly

Kia Sorento Booster & Master Cylinder Assembly

Kia Sorento Booster & Master Cylinder Assembly

Kia Sorento Booster & Master Cylinder Assembly

Kia Sorento Cylinder Assembly-Brake

Kia Sorento Brake Master Cylinder

Kia Sorento Brake Master Cylinder Parts Questions & Experts Answers

Related Kia Sorento Parts

Browse by Year