How do you remove and install the engine components, including the camshaft,Lash Adjuster and Rocker Arm on Kia Sportage for four cylinder engine?

Before now, to change the engine, set it to TDC position for cylinder number 1 and unbolt the wire of the bad connection from the terminal of the battery before unbolting the valve cover. For year 1994 to 1997 models, take off the distributor and for the models of the year 1998 and above, take off the camshaft position sensor. Then, remove all the timing belt covers, timing belt and all or some of the camshaft sprockets depending on the design. Check the camshaft thrust clearance with a dial indicator; if the same is higher than the above mentioned limit, then replace the camshaft thrust plate, camshaft, or cylinder head may be required. As for further remarks referring to the 1.6L SOHC engines, it is necessary to make the following notes: The 1.6L SOHC engines use the rocker shaft and equipment called hydraulic lash adjusters, which helps avoid additional movements of valves after their installation. Paint or label components before they are taken off so that they can be refitted correctly, counter-clockwise torque the rocker arm bolts, then pull out the rocker arm and shaft assembly and set them aside. To pull the camshaft without involving the cylinder head, you need to remove the distributor, the air cleaner assembly, reposition the under hood fuse box and then pull it straight up to extract it / remove the oil seal. For DOHC engines, these use two overhead camshafts with hydraulic lash adjusters; marking and storage of the parts should be done correctly. The camshaft sprocket bolts and sprockets should be taken off. Disconnect the camshaft bearing cap bolts with equal delicacy so that there will be no binding. Providing identification marks, undo the bearing caps and draw out every valve lash adjuster and place them in different numbers of containers. Look for defects on all parts, use micrometer to measure the camshaft journals, and lobes, and check for the oil clearance by using Plastigage. Replace any worn components. To install the new camshaft, one should pour some clean engine oil on the new camshaft oil seal and the bearing journals and lubricate the camshaft lobes before fitting the camshaft and the thrust plate. Were hydraulic lash adjusters eliminated, refill the rocker arm cavity with oil and then reinsert the adjusters. Reassembly the rocker arm assembly, tighten the bolt in sequential numbers, then the camshaft sprocket and timing belt should be put back. For the 2.0L DOHC engine, carry out the following before and after installation of the camshaft and lash adjusters, lubricate the lash adjusters and the bearing journals of the camshaft. Ensure that the Mark 'A' aligns with mark 'A' when assembling the engine. Lash adjusters are available to adjust the valve clearances and the thickness of the shims must be measured so that it can be replaced by the new one with the standard specifications. Do the adjustment again and again until the clearances of other valves are within the predetermined level.

Genuine Kia Sportage Camshaft

Cam

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

19 Camshafts found

View related parts
Kia Sportage Camshaft Assembly-Intake
Part Number: 241002G000
$175.25 MSRP: $250.72
You Save: $75.47 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Camshaft, Intake Camshaft
- Replaces: 241002G600, 241002G100, 241002G010, 241002G650
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2010-2015 Kia Sportage | 2.0L - Theta 2, 2.4L - Theta 2 | Wagon - 5Door 5P
View related parts
Kia Sportage Camshaft Assembly-Exhaust
Part Number: 242002G700
$288.62 MSRP: $415.40
You Save: $126.78 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Exhaust Camshaft
- Replaces: 242002G620
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2010-2015 Kia Sportage | 2.0L - Theta 2 | Wagon - 5Door 5P
View related parts
Kia Sportage Camshaft Assembly-Intake
Part Number: 241002GTB0
$370.72 MSRP: $533.57
You Save: $162.85 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Camshaft, Intake Camshaft
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2016-2022 Kia Sportage | 2.0L - Theta 2, 2.4L - Theta 2 | Wagon - 5Door 5P
View related parts
Kia Sportage Camshaft Assembly-Exhaust
Part Number: 242002G750
$220.92 MSRP: $316.05
You Save: $95.13 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Camshaft
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2014-2015 Kia Sportage | 2.4L - Theta 2 | Wagon - 5Door 5P
View related parts
Kia Sportage Camshaft Assembly-Exhaust
Part Number: 242002GTA0
$367.97 MSRP: $529.60
You Save: $161.63 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Camshaft, Exhaust Camshaft
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2016-2022 Kia Sportage | 2.0L - Theta 2 | Wagon - 5Door 5P
View related parts
Kia Sportage Camshaft Assembly-Exhaust
Part Number: 242002G000
$269.73 MSRP: $388.22
You Save: $118.49 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Camshaft, Exhaust Camshaft
- Replaces: 242002G650, 242002G100, 242002G600, 242002G010
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2010-2013 Kia Sportage | 2.4L - Theta 2 | Wagon - 5Door 5P
View related parts
Kia Sportage Camshaft Assembly-Exhaust
Part Number: 242002GGA0
$305.30 MSRP: $439.40
You Save: $134.10 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Camshaft, Exhaust Camshaft
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2016-2022 Kia Sportage | 2.4L - Theta 2 | Wagon - 5Door 5P
View related parts
Kia Sportage Camshaft Assembly-Exhaust
Part Number: 2420023770
$437.75 MSRP: $630.03
You Save: $192.28 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Camshaft
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2005-2010 Kia Sportage | High Grade, Middle Grade | 2.0L, 2.0L - Beta | 5 Door Wagon, Wagon - 5Door 5P
View related parts
Kia Sportage CAMSHAFT Assembly
Part Number: 2410023770
$267.44 MSRP: $384.92
You Save: $117.48 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Camshaft Assembly-Intake; Camshaft
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2005-2010 Kia Sportage | High Grade, Middle Grade | 2.0L, 2.0L - Beta | 5 Door Wagon, Wagon - 5Door 5P
View related parts
Kia Sportage CAMSHAFT Assembly
Part Number: 0K95412420
$293.96 MSRP: $423.09
You Save: $129.13 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Camshaft Assembly-Intake; Camshaft
- Manufacturer Note: GLS
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 1997-2002 Kia Sportage | High Grade, Low Grade, Middle Grade | 2.0L | 2 Door 5 Canvas Top, 5 Door Wagon
View related parts
Kia Sportage CAMSHAFT-Exhaust LH
Part Number: 2421037201
$261.31 MSRP: $376.10
You Save: $114.79 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Camshaft-Exhaust,LH; Camshaft
- Position: Driver Side
- Replaces: 2421037211, 2420037301
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2005-2010 Kia Sportage | High Grade, Middle Grade | 2.7L, 2.7L - Delta | 5 Door Wagon, Wagon - 5Door 5P
View related parts
Kia Sportage CAMSHAFT-Intake RH
Part Number: 2491037201
$290.86 MSRP: $409.08
You Save: $118.22 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Camshaft-Intake,RH
- Position: Passenger Side
- Replaced by: 2491037211
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2005-2010 Kia Sportage | High Grade, Middle Grade | 2.7L, 2.7L - Delta | 5 Door Wagon, Wagon - 5Door 5P
View related parts
Kia Sportage CAMSHAFT-Intake LH
Part Number: 2411037201
$184.73 MSRP: $256.57
You Save: $71.84 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: CAMSHAFT-Intake,LH
- Position: Driver Side
- Replaced by: 2411037211
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2005-2010 Kia Sportage | High Grade, Middle Grade | 2.7L, 2.7L - Delta | 5 Door Wagon, Wagon - 5Door 5P
View related parts
Kia Sportage CAMSHAFT-Intake, LH
Part Number: 2411037211
$179.34 MSRP: $256.57
You Save: $77.23 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: CAMSHAFT-Intake,LH; Camshaft
- Position: Driver Side
- Replaces: 2411037201
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2005-2010 Kia Sportage | High Grade, Middle Grade | 2.7L, 2.7L - Delta | 5 Door Wagon, Wagon - 5Door 5P
View related parts
Kia Sportage CAMSHAFT-Exhaust RH
Part Number: 2471037201
$239.74 MSRP: $345.05
You Save: $105.31 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: CAMSHAFT-Exhaust,RH; Camshaft
- Position: Passenger Side
- Replaces: 2471037211, 2470037301
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2005-2010 Kia Sportage | High Grade, Middle Grade | 2.7L, 2.7L - Delta | 5 Door Wagon, Wagon - 5Door 5P
View related parts
Kia Sportage Camshaft-Exhaust
Part Number: 0K01312440
$243.17 MSRP: $349.99
You Save: $106.82 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Camshaft Assembly-Exhaust; Camshaft
- Manufacturer Note: GASOLINE
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 1997-2002 Kia Sportage | High Grade, Low Grade, Middle Grade | 2.0L | 2 Door 5 Canvas Top, 5 Door Wagon
View related parts
Kia Sportage CAMSHAFT Assembly-EXHAUS
Part Number: 242002S050
$268.68 MSRP: $386.70
You Save: $118.02 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Camshaft
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2023-2024 Kia Sportage | 2.5L-THETA-III | Wagon - Long 5Door 5P
View related parts
Kia Sportage CAMSHAFT Assembly-EXHAUS
Part Number: 242002M801
$276.61 MSRP: $398.12
You Save: $121.51 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Camshaft
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2023-2024 Kia Sportage | 1.6L-Gamma-II | Wagon - Long 5Door 5P
View related parts
Kia Sportage CAMSHAFT Assembly-Intake
Part Number: 241002S050
$282.51 MSRP: $406.60
You Save: $124.09 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Camshaft
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2023-2024 Kia Sportage | 2.5L-THETA-III | Wagon - Long 5Door 5P

Kia Sportage Camshaft

If you're in search of top-notch, reasonably priced OEM Kia Sportage Camshaft, then you've found the perfect spot. Our website boasts an extensive inventory of Kia Sportage Camshaft, all priced at the market's premier price. Rest assured, every genuine part we offer comes with a warranty straight from the manufacturer.

Kia Sportage Camshaft Parts Questions & Experts Answers

Camshaft Assembly-Intake
241002G000
Q: How do you remove and install the engine components, including the camshaft,Lash Adjuster and Rocker Arm on Kia Sportage for four cylinder engine?
A: Before now, to change the engine, set it to TDC position for cylinder number 1 and unbolt the wire of the bad connection from the terminal of the battery before unbolting the valve cover. For year 1994 to 1997 models, take off the distributor and for the models of the year 1998 and above, take off the camshaft position sensor. Then, remove all the Timing Belt covers, timing belt and all or some of the camshaft sprockets depending on the design. Check the camshaft thrust clearance with a dial indicator; if the same is higher than the above mentioned limit, then replace the camshaft thrust plate, camshaft, or Cylinder Head may be required. As for further remarks referring to the 1.6L SOHC engines, it is necessary to make the following notes: The 1.6L SOHC engines use the rocker shaft and equipment called hydraulic lash adjusters, which helps avoid additional movements of valves after their installation. Paint or label components before they are taken off so that they can be refitted correctly, counter-clockwise torque the rocker arm bolts, then pull out the rocker arm and shaft assembly and set them aside. To pull the camshaft without involving the cylinder head, you need to remove the distributor, the air cleaner assembly, reposition the under hood fuse box and then pull it straight up to extract it / remove the oil seal. For DOHC engines, these use two overhead camshafts with hydraulic lash adjusters; marking and storage of the parts should be done correctly. The camshaft sprocket bolts and sprockets should be taken off. Disconnect the camshaft bearing cap bolts with equal delicacy so that there will be no binding. Providing identification marks, undo the bearing caps and draw out every valve lash adjuster and place them in different numbers of containers. Look for defects on all parts, use micrometer to measure the camshaft journals, and lobes, and check for the oil clearance by using Plastigage. Replace any worn components. To install the new camshaft, one should pour some clean engine oil on the new camshaft oil seal and the bearing journals and lubricate the camshaft lobes before fitting the camshaft and the thrust plate. Were hydraulic lash adjusters eliminated, refill the rocker arm cavity with oil and then reinsert the adjusters. Reassembly the rocker arm assembly, tighten the bolt in sequential numbers, then the camshaft sprocket and timing belt should be put back. For the 2.0L DOHC engine, carry out the following before and after installation of the camshaft and lash adjusters, lubricate the lash adjusters and the bearing journals of the camshaft. Ensure that the Mark 'A' aligns with mark 'A' when assembling the engine. Lash adjusters are available to adjust the valve clearances and the thickness of the shims must be measured so that it can be replaced by the new one with the standard specifications. Do the adjustment again and again until the clearances of other valves are within the predetermined level.